Abbott Mesh Belt Brazing Furnace. Model #4ZSCR-12-144HH4-2150, S/N AB574-16997-PHC-0305. Built by Abbott Furnace in 2007 this furnace has seen very limited use in an aerospace company. Electrically heated, 145 KW/3phase/60 HZ/480 Volts, maximum operating temperature of 2250F. Set up for hydrogen, nitrogen and Argon. 4 zones of control. Cooling Chamber: 17’ft long, Width of work zone: 12″ wide, Silicon Carbide Muffles (the best). Dimensions: 14″ wide x 7.5″ high. Belt Speed: 2″ per minute to 10″ per min
Allen Bradley Controls, Dew Point Meters, Programmable hydrogen meters. Flow Meters are top of the line Waukee Flo-Meters. Total Furnace dimensions: approximately 35’ft Long (includes loading and unloading) x 4.5’ft wide x 8’ft tall. Furnace includes new belt and many spare parts. Originally used with hydrogen between 1850F and 1950F. This furnace has all the bells and whistles and has been professionally uninstalled, electrical wires match marked and rigged out. Buyer is only responsible for shipping.
ASKING ONLY $50,000 USD!
Item # C327
AGF Rotary Retort Line
AGF Rotary Retort Line. AGF model 280 rotary retort line. Includes lift bucket, dump and feed loader, high heat rotary retort furnace, rotary washer and temper. Set up for Neutral hardening and Carbo Nitriding with natural gas and endo atmosphere. The retort is 16″ OD X 14 ½” ID and 17’ long. Total weight 2600 pounds, HW material. Spare retort included. Buyer is responsible for disconnecting and loading however there are large overheads cranes in the area making removal quite simple. Asking price for everything including the spare retort is $95,000 USD.
Asking Price: $95,000 USD.
Item # C326
SOLO Swiss Mesh Belt Furnace
SOLO Swiss Mesh Belt Furnace. Built in 1995 this furnace has a max temperature of 1150 C with a main voltage of 3 x 400V – 50 Hz. The power input is 40 kw and has a heating zone power of 3 x 13 kw. The heated length is 4000 mm and the cooled length is 6000 mm with a channel section of 220 x 60/100 mm. The belt width is 200 mm and the working height with the belt is 40 mm. The conveyor belt speed is 90 cm per minute. This furnace was used to anneal stainless steel parts and various other materials (Brazing, Tempering, Hardening). Located in France.
Price on request.
Item # C325
Sinterite Mesh Belt Conveyor Furnace
Sinterite Mesh Belt Conveyor Furnace. 120” long preheat, 2 zones, silicon carbide heating elements with metallic muffle. 180” long high heat with 3 zones of control, silicon carbide heating elements and ceramic muffle. 180 KW, 480/3/60. Belt width 12” with 4” clearance over belt. Overall dimensions 60”W X 75”H X 54’-0”L. Cooling length 282”. Preheat is rated for 1100 degrees C and high heat is rated for 1180C. New in 2000 it has seen very limited production and is in excellent condition. Has pre-heat bubbler. New pre-heat muffle, new belt, and several new glo-bars.
Asking $80,000.00 USD or best offer.
Item # C324
C.I. Hayes Mesh Belt Furnace
C.I. Hayes Mesh Belt Furnace. LAC Type. Work Zone: 12″ Wide Belt, 12″ High work area, 12′ heat, 12′ cool with 3 zones of temperature control. 1120C maximum temperature (2000F operating temperature). Power: 220V, 75KW, 212Amp, 60Hz , 3Ph. “Air Products” Gas Mixing Panel (N2, H2). Footprint: 9’W x 54’L (90’L Belt), 10’H + ductwork. Extra set of cooling muffles. Please call for pricing.
Item # C323
Aichelin Cast Link Furnace Line
Aichelin Cast Link Furnace Line. The line consists of a loading table, cast link belt hardening furnace, oil quench, cross conveyor, post wash and two continuous tempering furnaces. High belt is 24” wide X 300” long with a capacity of 336 Kg/h. Nitrogen/Methanol atmosphere. Electrically heated 300 kW. Operating temperature of 1650F. Quench oil tank holds 7,000 litres. Air/oil quench oil cooler. Post wash has oil skimmer. Both tempering furnaces are electrically heated, 57 kW each. Belt widths 20” X 250” long. Maximum operating temperature of 575F. Installed in 2005 and currently used for automotive bearings. Complete installed and in operation until March 2017. Excellent condition.
Item # C322
Surface Combustion Rotary Hearth Furnace Line
Surface Combustion Rotary Hearth Furnace Line. This system was designed for heat treating and straightening crankshafts and consists of a rotary hearth furnace, 2 Gleason straightening presses and a robot for loading/unloading. The furnace is S/N CC11590-1 with an outside diameter of 17′ 3″, inside 15′, inside height of 2′ 11″ with an overall height of 8″ 6″. Built August 1979. Gas fired with 8 trident tubes. Atmosphere is Endo/Natural gas. Nominal tray size is 5″ X 21″, number of tray positions 60, tray loader/unloader length 10′ 6″. Hearth has ceramic tray support and guide tiles and embedded in 12″ thick insulating firebrick. Sidewalls consist of 9″ of insulating firebrick backed with 4 1/2″ of insulating block. Alloy and brickwork are both excellent. System is complete, installed but not in operation.
Asking $50,000 USD.
Item # C321
Austempering System. Ipsen Model SG500, S/N52822. Shaker hearth style hardening furnace is capable of 500 pounds/hour, 1850F operating temperature, gas fired 800,000 BTU’s/hour with an 18” wide tray. Temper has an operating temperature of 800F and a heat input of 300,000 BTU’s. Controls on both are Honeywell UDC units. Entire system consists of a magnetic conveyor loading system, Ipsen shaker-feeder-hopper. Mitsibushi variable speed AC drive on salt conveyors, 900 gallon wash tank with 30” conveyor and 280 gallon rust inhibitor tank with 32” conveyor. Currently installed but not in production. System is in reasonable condition but has not been used for some time.
Asking $20,000 USD or best offer.
Item # C320
Lindberg Pusher Line
Lindberg Pusher Line. Line consists of a 170F prewash, purge, 1500F pre-heat, 1550F high heat, 350F oil quench, air cool, 170F hot water wash, cold air quench, 375F three zone temper and 460F draw temper. Built and installed in 1976, electrically heated. Designed for martensitic heat treating of 52100 bearing steel. 10 trays in system each 46” X 28”. Working height of 24”. Each tray is capable of 700 pounds. Controls have been updated recently with a new SSI MCA6010 three gas analyzer. Currently installed and in production. Very well maintained and in excellent condition.
Very attractive asking price.
Item # C319
CI Hayes High Temperature Pusher Furnace
CI Hayes High Temperature Pusher Furnace. C.I. Hayes model MY-040848-94PH high temperature pusher furnace. 4″ opening above the hearth, 8″ tray width. Max. Temp: pre-heat 1100 C, High Heat 1700 C. 94″ long preheat, 1 control instrument/1 zone, 15 KW@440/3/60, metallic heating elements. 48″ high heat, 1 instrument, 3 control zones, 45 KW2440/3/60, molybdenum heating elements. 48″ metallic front tunnel with nitrogen curtains and burn off. 3 cooling sections. each 36″ long, 1 section is insulated and all are water jacketed. Rear tunnel with nitrogen curtains and burn off. Multiple atmosphere inlets, for hydrogen/dissociated ammonia with nitrogen purging. Pusher screw drive. Atmosphere bubbler. High heat chamber recently rebuilt. Overall Dimensions; 6’H x 4’-6”W x 39’L (Approx.)
Asking $100,000 USD.
Item # C317
CI Hayes High Temperature Pusher Furnace
CI Hayes High Temperature Pusher Furnace. Model MY-040848-94PH. 4” opening above furnace hearth. 8” tray width. Maximum temperature of the pre-heat is 1100C, maximum temperature of the high heat is 1700C. 94” preheat, 1 control instrument/1 zone, 30KW@440/3/60, metallic heating elements. 48” high heat, 3 instruments, 3 control zone, 45KW @ 440/3/60, moly heating elements. 48” metallic front tunnel with nitrogen curtains and burn off. 3 cooling sections each 36” long, 1 section is insulated and all are water jacketed. Rear tunnel with nitrogen curtains and burn off. Multiple atmosphere inlets for hydrogen/dissociated ammonia with nitrogen purging. Pusher screw drive. Atmosphere bubbler. Return conveyor system. High heat chamber recently rebuilt. Overall dimensions 6’ high X 7.5’ wide X 39’ long (approximate). Excellent condition. Furnace was used for co-firing, can be converted for sintering with preheat muffle.
Asking $110,000 USD.
Item # C314
Roller Hearth Furnace (Atmosphere)
Roller Hearth Furnace (Atmosphere). Manufactured by Wellman in 1982. Model #AL-81-180 RH, S/N 180. Working dimensions of 60” Wide x 42’ Long x 14” High – 4800#/HR. Electric – 480/3/60 – 469 KW (over (4) Zones of Control). Operating temperature of 1650° F. Brick Lined Atmosphere Capable Roller Hearth Furnace complete with (4) Zones of Control, Heating Elements above and below Rolls, Transformers, 25’ Slow Cool Chamber (Air Cooled with Fans), and Variable Speed Drive. Free Standing Control Panels with Watlow Digital Controllers ((1) Per Zone), Watlow High Limits, and SCR Power Controls. Overall dimensions; Entrance Chamber: 12’Wide x 14’ Long x 10’ 6” High. High Heat Chamber: 10’ 6” Wide x 30’ Long x 10’ 6” High. Cooling Zone: 12’ Wide x 27’ Long x 10’ 6” High. Approximate weight 80,000 pounds. Very good condition.
Asking $225,000 USD.
Item # C312
Surface Combustion (Pifco) Roller Hearth Line
Surface Combustion (Pifco) Roller Hearth Line. 60″ x 60″ Trays capable of 4000 lbs per tray. This line is gas fired and includes an SSi datalogging system. Also includes SBS Heat Exchangers and has waulkeetronic flow meters.
Asking Price: $450,000 USD. Must be removed within the next few months All Offers Considered.
Item # C311
Ipsen Pusher Line P-12
Ipsen Pusher Line P-12. Rebuilt by JL Becker Company. This is a complete line which includes; a Pre-wash, Hardening Furnace, Oil Quench, Post Wash, and Temper. It’s setup for endothermic atmosphere and is currently installed and operating. Hardening furnace is capable of 1750 F and has 5 zones of control. Gross load 1000 pounds. 460 Volts/3 Phase/60Hertz. 3,000,000 BTU/hr heat input, gas fired, tray size 30″ x 30″ x 29″ overall with loading. Good overall condition.
Asking Price $250, 000 USD. Must be removed within the next few months All Offers Considered.
Item # C308
AFC Mesh Belt Hardening Furnace
AFC Mesh Belt Hardening Furnace. Manufactured by Atmosphere Furnace Company this furnace has working dimensions of 6″ high x 54″ wide x 12′ long (heated section). Gas fired with radiant tubes. Operating temperature of 1800F. S/N 6948. Temperature Controls: Free standing enclosed panel. Honeywell solid state digital readout indicating controllers, L&N overtemps. L&N strip chart temperature & carbon recorder. Marathon Monitors Carb-Pro carbon control. Description & Features: Fiber lined. Heated by (9)North American 4724-2-E burners firing into recuperated U-tubes. Two zones of control. Rear zone has a roof mounted recirculating fan. Cold belt return. Furnace has a flame curtain and complete combustion controls and safeties. Includes quench tank and conveyer.
Asking $75,000 USD.
Item # C302
Mesh Belt Austemper Lines (2 available)
Mesh Belt Austemper Lines (2 available). Built by AFC-Holcroft these are mesh belt, gas fired austemper lines. Parts to be processed are metered on to the variable speed, 30” wide mesh belt, travel through an 8” long high heat zone, drop into an electrically heated salt quench tank then are carried on a conveyor out of the quench tank and into a washer. A circulating fan distributes heat and atmosphere evenly though the heating area. Heat is supplied by two U shaped radiant tubes that are recuperated. SSI controls monitor and control the atmosphere gases. Furnaces were in operation until March 2015. One furnace is 1989 vintage the other is a 2000 vintage. Both are complete, in very good condition and currently in storage. Asking $95,000 USD for the newer system and $75,000 USD for the older system.
Item # C301
Cast Link Belt Quench and Temper Line
Cast Link Belt Quench and Temper Line. Manufactured by Rogers Engineering 4,000 pounds/hour cast link belt furnace line consisting of a 1750F high heat furnace and 1700F temper furnace. Serial # CC-3977-0 (1997). High Heat Furnace: 48″W Omega Cast Link Belt, 4″ pitch, 3″ sides. Furnace has a 30’L heating section. Four (4) zones of control with three (3) roof mounted in the last three (3) zones. Maximum operating temperature of the hardening furnace is 1750°F. Furnace is radiant tube heated with recuperators. Furnace is currently set up for Endothermic w/Enriching Natural Gas & Air. Total BTU’s for hardeneing furnace is 3,180,000 BTU/HR. Controls; All mounted in a free standing panel includes Allen Bradley PLC w/HMI Touchscreen, Honeywell UDC Digital Temperature Controls, SSi Carbon Controls. Voltage 480/3/60/200kW.
Tempering/Anneal Furnace: 60″W mesh belt with support rollers. Furnace has a 35’L heating section. Four (4) zones of control with four (4) roof mounted fans. Maximum operating temperature is 1700°F. Total BTU’s for the tempering/annealing furnace 3,790,000 BTU/HR. Please note that this furnace has two (2) different modes of operation. Click on ‘PDF” below for more information on the different modes of operation.
The sequence of this furnace is as follows:
– Load parts into pre-wash dump loader
– Pre-Wash, 190°F, Gas Heat
– Parts vibrate onto mesh (soft load) then onto cast link belt.
– High heat cycle
– Quench cycle, 200°F, Gas Heat, 8000 Gallon
– Wash cycle, 190°F, Gas Heat
– Temper cycle
– Oil blackening cycle
– 5600 CFH Air Cooled Endothermic Gas Generator
– SBS Air to Oil Heat Exchanger which consists of three (3) 5 H.P. fans.- Manuals & Drawings
Very good condition, available immediately.
Asking $650,000 USD.
Item # C299
Sunbeam Rotary Hearth Furnace
Sunbeam Rotary Hearth Furnace. Working diameter of 6’, 8 station hearth, each station is 12” wide x 18” deep x 12 “ high. The door opening is 1’-6” wide X 10” high. Gas fired, 620,000 BTU’s, 3 radiant tubes and an operating temperature of 1750F. Built in 1977 and used for neutral hardening. Also included is a robotic arm for loading/unloading. The furnace is installed and in running condition, brand new radiant tubes and a rebuilt fan. All manuals and drawings are included. Good overall condition.
Asking $40,000 USD.
Item # C296
C.I. Hayes High Temperature Tube Furnace
C.I. Hayes High Temperature Tube Furnace. Model MY-0002.528, 2-1/2″ ID Tube x 28″ Long Heating Chamber. Operating temperature of 1700ºC, 10.5 KW, Single Zone Control with overtemp protection. Overall dimensions of 75″ H x 32″ W x 91″L. Hydrogen Atmosphere. Included is an automatic loader.
Asking Price $21,000 USD / OBO.
Item # C283
Denton Thermal Systems (O’Brien & Gere) 2150˚F Rotary Hearth Furnace System
Denton Thermal Systems (O’Brien & Gere) 2150˚F Rotary Hearth Furnace System. Includes high temperature furnace, Nitrogen-Methanol Panel and Quench Press. Working Zone: 6 ft Diameter Hearth, Door Opening is 14″W x 13″H Overall Size: 9ft-8in Diameter x 10ft-10″Tall. Heating: Electric, 125 kW, 1 Zone, Globar Heating Elements. Power Requirement: 200 Amps, 480V/3Ph/60Hz. Temperature Rating: 2150˚F. Water Requirement: 3 GPM. Air Requirement: 100 PSI. Controls: GE90 PLC. Honeywell Temperature Controller and Overtemp (missing but will be replaced). Marathon Monitors Carbon Control System. Includes Quench Press that was handling up to 5″ Diameter bearings. Prior user reference available upon request.
Asking price: $29,000 USD.
Item # C269
CI Hayes Mesh Belt Furnace
CI Hayes Mesh Belt Furnace. Working dimensions of 5″ over belt, 12” wide X 120” of heated length. Electrically heated 230/3/60, operating temperature of 2100F. Model LAC. Temperature controls are new state of the art, control panel with Honeywell sold state digital readout controller and overtemp for each of three zones, includes volt and amp meters. Full alloy muffle in hot zone. 20’ long sealed water jacketed cooling. Globar heating elements over and under the belt. (3) zones of control. (4) argon flowmeters. Dayton AC inverter provides adjustable belt speed. Updated SCR controls. Muffle and belt are new. Very good condition.
Asking $39,000 USD.
Item # C265
Sunbeam Pusher Carburizer
Sunbeam Pusher Carburizer. This is a very unusual style of furnace and perfect for carburizing of large gears, bearings or races. Working dimensions of 50″ X 50″ X 34″ high. Operating temperature of 1750F. 3,000 pound capacity. Gas fired 12 Honeywell composite single ended recuperated tubes (recently replaced). Surface Casemate controls. 1800 gallon quench tank. System does not need a pit. Comes with a spray washer, temper and an oversized IHRE air cooled quench oil cooler. System is installed but not currently in use. Very good condition.
Asking $40,000 USD.
Item # C219
ABBOTT MODEL 6ZSCR-18-432HH6-VC-2150
ABBOTT MODEL 6ZSCR-18-432HH6-VC-2150. 18″ wide belt, 3″+ opening over the belt, 432″ heating chamber (silicon carbide muffles), six zones, 36″ long vari-cool with 162″ of additional cooling including two curtain boxes. 2150 deg.F. max temp., piped for dissociated ammonia atmosphere and nitrogen purge, 335 kw @ 480/3/60,Honeywell UMO 800 controller/programmer, OAD: 84″ w x 90″ h x 720″ l. Currently used for annealing knife blades but with a little effort a metallic muffle in the front half of the heating chamber could be added for debinding and sintering of PM parts.