Inductoheat /Lepel Induction Power Supply. This is a Lepel/ Inductoheat SP5-40 kW, 3/10 kHz SCR type induction heating power supply with a separate Heat Station (I believe this could be operated at 3 kHz but the heat station is currently arranged for 10 kHz). This is an “HS-3” Heat Station with 3 capacitors and a Jackson Transformer with ratios of 5-3 to 17-3. The Inductoheat SP5 has been a proven reliable power supply for heating and heat treating for many years. It can be used for short heat times as it has fast and consistent ramp up to set power. There is no warranty but it is sold with the assurance it is in good working order. It has recently been connected and tested in our facility. I can supply a video of the unit in operation. Start up and Training service is available at extra cost by an experienced induction heating service engineer. Excellent condition.
Asking $19,500.00 USD
Item # I174
Ajax/Tocco Induction Heating Power Supply & Heat Station
Ajax/Tocco Induction Heating Power Supply & Heat Station. Manufactured by Ajax/Tocco in August 2005. 480V three phase input is rated to be 1.2MW (1200KW). 660V three phase input is rated to be 2.2MW (2200KW). Unit requires three phase input of 480V, 2500A. System is deigned to work at 2.5 kHz in frequency. Requires 65 GPM of cooling. Buyer must have a dedicated transformer at the three phase input for this machine. Buyer must provide their own coils, bus, and water-cooled cables to attach power supply to heat station and heat station to coils. Limited warranty available. Note: Currently set up to work at 480V input voltage. In order to switch to 660V, buyer needs to change the input breaker. Excellent condition.
Asking $139,000 USD.
Item # I173
125 Kw Ajax Induction Generator
125 Kw Ajax Induction Generator. Output is 125 Kw, Frequency 300KHZ, 460 Volt, Line Current 352 Amps. Foot Print 48” x 80” x 78”. PLC operated, Optical Infrared Pyrometer Temperature Control. Approximately 100 Induction Coils. Spare Load Coil Transformer. Lepel Heat Exchanger Lift and Rotate Fixture. Good Operating Condition.
Asking Price: $15,250.00 USD
Item # I172
Dual Spindle Induction Scanner
Dual Spindle Induction Scanner. Manufactured by Inductoheat this is an Inductoheat Statiscan II 200 Kw, 30khz vertical Induction scanner. This is a moderately used piece of equipment. It was used in a machine shop operation for a variety of parts. It appears to be in very good condition with some minor maint. required. Power Supply is IGBT type. This was in operation until a couple of weeks ago when it was replaced with a newer scanner. It has a 24” scanning capacity. (Replacement value est. $200,000)
It is available with;
• Dual Output Bus with shorting bar for single coil operation. (replacement value est. $4,000 +/-)
• Nine (9) MIQ (machined integral quench) Coils, 1 – 5/8” bore, 1- 7/8” bore,
1 – 1 ¼” bore, 2 – 1 ½” bore (need repair), 2 – 2” bore, 2- 2 – 2 ½” bore. All are in good or like new condition except the 1 ½”. (Replacement value est. $15,000 +/-)
• Spare Durant Counter (Replacement value est. $2,000). This model is a little simpler and less complex than more recent PLC or PC controls. I believe it would lend itself to a shop with less experienced operators or with frequently changing operators.
• Some (if not all) Documentation.
Asking Price: $75,000.00 USD
Item # I171
50 Kw Lepel Generator
50 Kw Lepel Generator, 350 KHZ,460V, 160 amps. Lepel heat exchanger included. PLC controlled processing, Optical Infrared Pyrometer controller for heating each part to the same temperature. Parts are then removed from the coil and immersion quenched in the appropriate media. Tempering follows.
Asking Price: $9750.00 USD
Item # I164
Ajax Tocco Induction Power Supply
Ajax Tocco Induction Power Supply. Model #OL-426-150-3/10-00M. Manufactured 12/06. Serial Number: 46-1128-11. Wiring Diag.: WD-287513. CKT.BKR. AMPS. : 400. Input Ratings: Volts Min./Max. : 432/528 P.F. : 82 Amps.Max. : 291 KVA : 220 Freq.Hz. : 60Hz Phase : 3 Output Ratings: Volts : 512 KW : 150 Amps. : 389 Freq.Hz. : 3/10 KHz Phase : 1 This unit was sold new to Caterpillar in 2006 and never installed and never used. Excellent condition.
Asking $33,000 USD.
Item # I160
Ajax Tocco Power Supply (un-used)
Ajax Tocco Power Supply (un-used). Ajax Tocco Inductron PT power supply, capacity: 450kW. Frequency: 3-10 kHZ. Output Voltage: 400 *. Year of manufacture: 2006. This unit was never installed and is unused. *Price quoted from Ajax Tocco to convert output voltage from 400 to 800 including parts and labor is $15,230. New this unit was $86,000 USD, http://www.ajaxtocco.com/applications/documentlibrary /Inductron%20PT_092003.pdf
Asking $39,000.00 USD.
Item # I158
Induction Power Supply
Induction Power Supply. Manufacturer Inductoheat/Elphiac. Model Number: DC18T+HF08. S/N 2177DC. 335 kW, 200 kHz, 750V Output. Input Voltage: 460/3/60/448 KVA/562 Amps. Output Voltage: 335 kW/750V/200 kHz. Very good condition.
Asking $39,500.00 USD.
Item # I153
Raydyne Induction Heating System
Raydyne Induction Heating System. Input Voltage: 480V/3 Phase/60 Cycles/110 Amps, Output Voltage: 40 kW, 450 kHz, Year Built: 1985, Model of Power Supply: EI-40, Serial Number of Power Supply: 41408901-B. Please note the RF Tube is missing. Includes a dual heat station with quench. Model of Heating/Quench Station: 10228201, Serial Number of Heating/Quench Station: 10228201B. This system is Government Surplus and appears to be fairly clean inside power supply cabinet. The power supply has a “Control Concepts” SCR power controller.